Free Download Driver For All Printer Series

A common Error code on Canon Copy Machine IR 2870/3570/4570/3030/3035/3045/3245

Error Code Canon IR
The existence of this guide may be able to troubleshoot error on copy of canon which usually make the customer was less comfortable. I hope your machine may be able to work well and always in condition. Thank you.
* Caution:
in some cases the error is happening inside the engine needs a reset in service mode, to enter into the program, the following are the steps:
Please press the button additional fungtion is in the monitor panel.
Press a number two and eight simultaneously
Press the back button additional fungtion and follow the instructions on the error code you were provided.
http://www.printerdriverupdates.com/2017/07/a-common-error-code-on-canon-copy.html
Canon IR Series


Canon imageRUNNER Series

Canon imageRUNNER C3200
canon imageRUNNER 2530
Canon imageRUNNER 1310
Canon imageRUNNER 1630
Canon imageRUNNER 1670F
Canon imageRUNNER 2016
canon imageRUNNER 1133
Canon imageRUNNER 2230
Canon imageRUNNER 2270
Canon imageRUNNER C2570
Canon imageRUNNER 2830
Canon imageRUNNER 2870
Canon imageRUNNER 3320
Canon imageRUNNER 3530
Canon imageRUNNER 3570
Canon imageRUNNER C3170U
Canon imageRUNNER C3170i
Canon imageRUNNER 4270
Canon imageRUNNER 4570
Canon imageRUNNER C4580
Canon imageRUNNER C4580i
Canon imageRUNNER 5070
Canon imageRUNNER 5570
Canon imageRUNNER 6570
Canon imageRUNNER C5870
Canon imageRUNNER C6870
Canon imageRUNNER 7086
Canon imageRUNNER 7095
Canon imageRUNNER 7105
Canon imageRUNNER 8070
Canon imageRUNNER 110
Canon imageRUNNER 150vp
Canon imageRUNNER 2022N
Canon imageRUNNER Advance c5035
Canon imageRUNNER Advance c5045
Canon imageRUNNER Advance c5025
Canon imageRUNNER Advance c5030
Canon imageRUNNER Advance c7055
Canon imageRUNNER Advance c7065
Canon imageRUNNER Advance c9065
Canon imageRUNNER Advance c9075

Error Code Canon IR

E000

The main cause: the main thermistor (TH1) has poor contact or an open thermal switch circuit. The (TP1) has a heater circuit. The open repair has a circuit. Open the RSKfaulty. The DC controller PCB faulty. Detection mode: 0000 after the main power switch is turned on, the temperature detected by the main thermistor does not reach 70 ºc.
Attention: mistakes have to be reset in service mode (COPIER > > FUNCTION CLEARERR >)

E001

The main cause: the main thermistor (TH1) has a short sub thermistor circuit. The (TH2) has detected overheating. The RSK is faulty. The DC controller PCB faulty. Detection mode: 0001 The main or sub thermistor thermistor has detected approximately230 º C or higher for 2 sec. 0002 this main thermistor detected 230 º C or higher (detection circuit hard) 0003 this sub thermistor detects about 236 ° C or higher. Attention: mistakes have to be reset in service mode (COPIER > > FUNCTION CLEAR ERR>)

E002

The main cause: the main thermistor (TH1) has poor contact or an open thermal switch circuit. The (TP1) have RSK circuit. Open the faulty. The DC controller PCB faulty.Detection mode: 0000 Temperature from the top fixing roller does not reach 100 °C within 2 minutes after it has exceeded 70 º c. caution: faults must be reset in service mode (COPIER > > FUNCTION CLEAR ERR >)

E003

The main cause: the main thermistor (TH1) has poor contact or an open thermal switch circuit. The (TP1) has a heater circuit. The open repair has a circuit. Open the RSKfaulty. The DC controller PCB faulty. Mode of detection: 0000 main thermistor detected a temperature of 70 ° C for 2 seconds or more after it has reaced 100 º c. caution: faults must be reset in service mode (COPIER > > FUNCTION CLEAR ERR >)

E004

The main cause: RSK has short-circuit. The DC Controller PCB faulty. Detection mode: 0000 The RSK is used to fix the heater drive found to have a short circuit (circuit detection hardware). Attention: mistakes have to be reset in service mode (COPIER >> FUNCTION CLEAR ERR >)

E005

The main cause: fixing the Web had been taken. Web fix Length sensor (PS45) is faulty. The DC controller PCB faulty. Detection mode: 0000 Long fixing the web has taken is more than the specified length. Note: After replacing the web improve, be sure to reset the two web counter in service mode: COPIER COUNTER > > MISC > FIX-WEB and COPIER COUNTER > > DRBL-1 > FX-WEB.

E010

The main cause: main motor (M2) is damaged. The DC Controller PCB faulty. Detection mode: the clock pulse is not 0000 arrived for 2 seconds or more after the main motor driving signal (MMFG) have been produced.

E012

The main cause: the drum Motor (M1) is damaged. The DC Controller PCB faulty. Detection mode: The clock pulse is not 0000 arrived for 2 seconds or more after the signal the motor drives the drum (DMFG) have been produced.

E013

The main cause: the waste toner feedscrew damaged. Waste toner sensor Clock (MSW2) damaged. The DC Controller PCB faulty. Detection mode: 0000 waste toner feedscrew from Rotation out of order, and the switch (MSW2) suppressed several times during a given period.

E014

The main cause: Motor repair (M19) damaged. The DC Controller PCB faulty. Detection mode: 0000 The signals clock motor is detected for 2 seconds or more continuously after fixing the motor drive has produced.

E020

The main cause: the connector hopper is left disconnected. Hopper motor(M9/M10) toner is faulty. The sensor (TS1/TS2) is damaged. The DC Controller PCB faulty. Detection mode: 0000 when printing, toner supply is ' 0 ' (the absence of toner) for 2 minutes.

E032

The main cause: copy data controller or remote diagnostic device is damaged. The main controller PCB faulty. Detection mode: 0001 though so connected, copy data controlleror remote diagnostic devices have become disconnected.

E061

The main cause: the laser shutter is broken. The laser unit is defective. Measurement of potential PCB damaged. The DC Controller PCB faulty. Detection mode: 0001 as a result of potential control, the potential of the surface of the drum (VL2) from a white background is about 200V
(Produces a solid black image) 0.0002 main charging Output used to print output and potential output after the laser drum surface has been made about 200V (producing solid black image).

E100

The main cause: BD PCB is damaged. The laser unit is defective. Laser driver PCB isfaulty. Broken cable (short circuit, open circuit). The controllerPCB DC faulty. Detectionmode: 0001 In 100 msec after the signal has been generated laser hard, the signal is not detected BD is 50 times or more
in 40 msecs. 0002 while the laser is active, the cycle signal BD found is beyond aspecific 10 times or more.

E110

The main causes: laser scanner motor (M15) is damaged. Broken cable (short circuit,open circuit). The DC Controller PCB faulty. Detection mode: 0001 • After laser scanner motor drive signal has been generated, the motor ready signal (LMRDY *) does not come to
15 seconds or more. (Stop-full speed, half speed-full speed) • during the period of 'full speed ' half-speed, signal the motor that does not come ready for 60 seconds ormore after
change the speed signal has been generated. • During the period of ' rotation at full speed ", signals the motor ready not detected 50 times or more (t 100 msecinterval).

E121

The main cause: the cooling fan controller (FM4) is damaged. Broken cable (short circuit, open circuit). The DC Controller PCB faulty. Mode of Detection0001 Though the cooling fan controller (FM4) is being driven, the signals clock (FM4LCK) don't come for 5 seconds or more.
Causes of E196Main: EEPROM on the DC controller PCB is damaged. The location ofthe EEPROM are wrong. The DC Controller PCB faulty. Detection mode: 1abb Whendata is written to the EEPROM, the data is written and read data do not match. 2abbWhen ID is read into the EEPROM and ROM ID into compared, discrepancies are found. 3abb when the ID in the ID in ROM and EEPROM than after the main power switch is turned on, a mismatch is found. a: No Chip 0 to 5 (0:1: IC104 IC105 IC109, 2:, 3:IC110, 4 : IC127, 5: IC130) address: bb damaged chips (bits)

E202

The main cause: the HP scanner sensor (PS39) damaged. The scanner motor (M3) is damaged. The reader controller PCB faulty. Detection mode: 0001 the scanner HP Sensor does not turn off even when the scanner has been moved forward 40 mm after the main power switch is turned on or the Start button has been pressed for. 0002 Scanner HP Sensor does not light up even when the scanner has moved 450 mm the code reverse. Caution is not indicated, and the button is locked. The code can be checked in the service mode (DISPLAY > > COPIER ERR).

E204

The main cause: ADF PCB controller is damaged. The reader controller PCB faulty. Detection mode: 0001 when printing, the image of the leading edge of signal does not come from the ADF code. Caution is not indicated, and the button is locked. The code can be checked in the service mode (DISPLAY > > COPIER ERR).

E220

The main cause: a lamp inverter PCB is damaged. The reader controller PCB faulty. Detection mode: 0001 Lamp inverter PCB were found to have errors.

E225

The main cause: scanning Light (xenon tube) is damaged. Faulty inverter PCB.CCD/AP PCB damaged. The reader controller PCB faulty. Detection mode: 0000 A certain signal level can not be achieved by getting the correction of CCD on power-on. 0002 Advantage edge correction value changed more than a certain level as compared to the value of correction used for previous sheet.

E240

The main cause: the controller to the main PCB. The DC Controller PCB faulty. Detection mode: 0000 an error has occured in the communication between the main controller PCB and the CPU from DC controller PCB.

E243

The main cause: Control Panel CPU PCB damaged. The main controller PCB faulty. Detection mode: 0000 an error has occured in the communication between the control panel CPU CPU PCB and the main controller PCB.

E248

The main cause: the EEPROM on the reader controller PCB is damaged. The reader controller PCB faulty. Detection mode: 0001 ID read into EEPROM when the main power switch is turned on and not in ROM ID match. 0002 When data is written to theEEPROM, the data is written and read data do not match. 0003 When data is written, the ID in the EEPROM and ROM ID found unsuitable.

E302

The main cause: CCD/AP PCB damaged. Broken cable (short circuit, open circuit). The reader controller PCB faulty. Detection mode: 0001 For shading, the reader controller PCB did not end up shading within 1 sec. 0002 in the reading flow, accumulation of white edges (processing) do not expire after a period of 10 seconds.

E601

The main cause: this cable is faulty (short circuit, open circuit). Hard disk drive is damaged. The DC Controller PCB is damaged. The main controller PCB faulty. Detection mode: 0000 main controller PCB has detected an error in the image was transmitted datawhile control between primary hard disk controller PCBand controller maindrive. 0001 PCB has found errors in control data image between governing PCB intransfer main and controllerPCB DC.

E602

The main cause of the cable is faulty (short circuit, open circuit). The isfaulty hard drive disk. The main controller PCB faulty. Fashion ofDetection0001 A mountain error is detected when the hard disk starts the boot ROM. 0002 upfrom an error reading data (from the hard disk) was detected when the hard disk starting from the boot ROM.
E607
The main cause of the fan hard disk (FM7) damaged. Cable damage (a shorthyphen, opencircuit). The DC Controller PCB faulty. OfDetection0000 mode While the fan hard disk (FM7) is being driven, the signals clock (FM7CLK) don't come for 5 seconds or more.

E677

The main cause of the Council the various printer (accessories) are broken. The maincontroller PCB faulty. Fashion ofDetection0001 an error has occured in the communication between the various

E710

The main causes of the DC controller PCB is damaged. The reader controller PCB faulty. The main controller PCB faulty. OfDetection0001 mode When the main power is turned on, the IPC (IC5021) on the PCB cannot be initialized readercontroller. 0002When the main power is turned on, the IPC (IC120) on PCB DCcontroller cannot be initialized. 0003 When main power is turned on, the IPC (IC1003) on the PCB maincontroller cannot be initialized.

E711

The main cause of the connector is not connected properly. PCBis remote diagnostic device is damaged. PCB copies the data controller is damaged. ADF isfaulty controller PCB. ADF PCB controller is damaged. Finisher isfaulty controller PCB. Mode of 0001 Detection data has been written to the error register IPC (IC5021) onthe reader controller PCB four times or more within 1.5 secs. 0002 data has been written to the error register IPC (IC120) onthe DC controller PCB four times or more in 2 secs. 0003 data has been written to the error register IPC (IC1003) of the solar controller PCB main four or more times within 2 seconds.

E712

The main cause of the connector is not connected properly. ADF 24-V isfaulty power supply. ADF PCB controller is damaged. The reader controller PCB isfaulty. OfDetection0001 Communication mode does not proceed in 3 seconds after the data has been writtento error register of IC communication (IPC) of the PCB ADFcontroller. 0002 bit transmission is not activated after a period of 10 seconds in thesync list of IPC(IC5021) on the reader controller PCB.

B

The main cause of the connector is not connected properly. Finisher gear powersupply PCB damaged. Finisher controller PCB is damaged. The controllerPCB DC faulty.OfDetection0000 IC-mode communication (IPC) on the controller finisher have goneout order.

E717

The main cause of the cable is faulty (short circuit, open circuit). Data copy of remote-control diagnostic orthe damaged. The main controller PCB faulty. OfDetection0001 The mode of copying the data controller or the controller circuit is damaged or anopen NE has been detected. Caution Fault must be reset in service mode (COPIER> > FUNCTION CLEAR ERR >).

E719

The main cause of the cable is faulty (short circuit, open circuit). Faulty coin vendor.The main controller PCB faulty. Mode of Detection0001 communication between the vendor and the main controllerPCB coins had been interrupted. Caution Fault must be reset in service mode (COPIER > > FUNCTION CLEAR ERR >).

E732

The main cause of this connector has poor contact. The reader controller PCB faulty.OfDetection0001 mode the main controller PCB has detected an error in the communicationbetween controller PCB and the main controllerPCB readers.

E733

The main cause of this connector has poor contact. The DC Controller PCB faulty. OfDetection0001 mode the main controller PCB has detected an error in the communicationbetween the DC controller PCB and the main controller PCB. CLEAR > ERR). Printer Board (accessories) and the main controller PCB.

E740

The main causes of LAN card is damaged. The main controller PCB faulty. Fashion ofDetection0001 error is detected on a LAN card at power-on (with cardinserted) 0.0002 A MAC address found faulty. 0003 LAN card register cannot be read.

E741

The main cause of the PCI bus connection is not right. The main controller PCB faulty. Fashion ofDetection0000 an error has occurred on the PCI bus.

E742

The main cause of RIP1 Board (accessory) is damaged. The main controller PCB faulty. Fashion ofDetection0000 Error has been detected by the self diagnosis of RIPI.

E743

The main cause of this connector has poor contact. The main controller PCB faulty.Mode 0000 Detection controller PCB Readers have detected errors in the main controller PCB and communicationbetween controllerPCB readers.

E804

The main cause of the cable is faulty (short circuit, open circuit). DC power supply fan (FM6) is damaged. The DC Controller PCB faulty. OfDetection0000 mode While the supply of DC power driven fan, clock signal (FM6CLK) don't come for 5 seconds or more.

E805

The main cause of the cable is faulty (short circuit, open circuit). Fan feed (FM1) isfaulty. Heat dissipation fan (FM3) is damaged. The DC Controller PCB isfaulty. OfDetection0001 mode While a fan driven heat dissipation, signals clock (FM3CLK) don't come for 5 seconds or more. 0002 While fan-driven feed, signals clock (FM1CLK) don't come for 5 seconds or more.

E824

The main cause of the cable is faulty (short circuit, open circuit). Main charging assemblycooling fan (FM2) is damaged. The DC Controller PCB faulty. OfDetection0000mode While charging the main cooling fan Assembly that is driven,

E412

The main causes of cooling fan (FM1) is damaged. ADF controller PCB faulty. OfDetection0001 mode While the cooling fan is driven, key signal (FMLCK) arrived to 100msec or longer.

E420

The main cause of the corrupted EEPROM. ADF controller PCB faulty. Detection mode of 0001 When the power button is turned on, the host machine backupdata fromEEPROM unreadable or the data, if read, has an error.

E421

The main cause of the corrupted EEPROM. ADF controller PCB faulty. Mode ofDetection0001 Backup data cannot be written to the EEPROM data or, if a clock signal is written, URerror.the (FM2CLK) don't come for 5 seconds or more.

E422

The main causes of communication IPC has errors. The lines of communication havean opencircuit. ADF controller PCB faulty. OfDetection0001 mode while the machineis in standby, communication with the hostmachine has been plagued for 5 secondsor more. or, while machineis in operations, communications with the host machine hasbeen disturbed during 0.5 seconds or more.

E500

The main causes of faulty controller PCB finisher. The DC Controller PCB faulty. OfDetection0001 modes of communication between the host machine and hasbeen finisher disconnected; This error is detected by the host machine.

E503

The main cause of saddle stitcher PCB controller is damaged. Finisher isfaulty controller PCB. OfDetection0002 mode of communication between saddle stitcher controller PCBand controller PCB has been plagued finisher.
E504
The main causes of the high Sensor (PS1) is damaged. Finisher controller PCB faulty.OfDetection0001 modes of communication between the sensor and the altitude controllerPCB finisher is not possible, or communications data has errors. 0002 communications between sensors and elevation controllerPCB finisher is not possible for a certain period of time. 0003 upon power-on, the connector from the sensor height found tobe disconnected. 0004 When height sensors are adjusted by using the DIP switches, anerror occurs during adjustment.

E505

The main cause of the corrupted EEPROM. Finisher controller PCB is damaged. Puncherdriver PCB is faulty. OfDetection0001 mode when the power switch is turned on, the amount of the check theEEPROM on the controller PCB finisher are found to have errors. 0002 When switch power is switched on, the number of checks on the PCBpons theEEPROM drivers who are found to have errors.

E512

The main causes of Motor delivery Hours the sensor (PI10) damaged. Delivery of themotor (M2) is damaged. Finisher controller PCB faulty. OfDetection0001 mode when the operation starts, as the hours required no arrivefrom shipping motor clock sensor. 0002 no clock pulse arrives while the paper are moving above 200 mm distanceof.

E530

The main cause of the home position sensor alignment Plate (PI6) damaged. The alignmentmotor (M3) is damaged. Finisher controller PCB faulty. OfDetection0001 fashion Plate alignment not to leave the home position when alignmentmotor has driven for 2 secs. 0002 Plate alignment did not return to the original position when themotor thealignment has driven for 2 seconds.

E531

The main causes of home stapler detect the position of the switch (MS7) damaged.Motor stapler (M6) is damaged. Finisher controller PCB ofDetection0001 faulty. Stapler mode does not leave home position when the motorhas stapler has been encouraged to 0.5 sec. 0002 stapler does not return to the position of the House when the motorhas stapler driven during 0.5 second.

E532

The main cause of the shift position sensor home stapler (PI7) damaged. The staplershift motor (M4) is damaged. Finisher controller PCB faulty. Mode ofDetection0001Unit of stapler does not leave home position when shiftmotor stapler has been boosted to 4 secs. 0002 stapler Unit not to go back to the position of the motor home when staplershift has pushed for 4 seconds.

E535

The main causes of Motor swing Clock sensor (PI20) damaged. Guide swing open Sensor (PI18) is broken. The area of the safety switch (MS3) damaged. Swing guideclosed detect the switch 2 (MS6) damaged. Motor swing (M7) is a finisher faulty. Thecontroller PCB faulty. OfDetection0001 mode Guide swing closed detect 2 switch does not light up on the swing motor whenthe has rotated CCW for 1 sec. 0002 Guideswing open Sensor does not light up when the motorhas swing has been rotated CW for 1 sec. 0003 When operating in the tray lifting motor, guide swing closed detectingswitch 2 was found to be off while the tray is in the 1/2 OFF safety switch areapositionof. 0004 clock no arrived to 200 msecs operating machine while the swing.

E540

The main cause of the home position sensor Tray (PI8) damaged. Tray 1/2 clocksensor Motor bearing (PI9/PI19) is broken. The upper limit of the tray switch detects (MS5) damaged. Tray bearing motor (M5) is damaged. Finisher controller PCB isfaulty. 0001 this ascent did not end in 15 seconds when the tray lifting motor isdriven, or home position, the tray can not be detected when the motor traylift has driven for 15 secs. 0002 While moving up the tray, the tray of detection limit switchis found on. 0003 When the tray lifting motor driven, clock pulse does not arrive 1/2 hour fromtheSensor for 200 msecs.

E584

The main cause of Sensor shutter open (PI5) damaged. Area security switch detects(MS3) damaged. The shutter closed detecting switch (MS4) damaged. TheNo. 2 feedmotor (M8) damaged. Finisher controller PCB faulty. OfDetection0001 mode the shutter closed does not light up when the switch detects the motor feed no.2 has beenrotated CCW for 1 second or more. 0002 Sensor shutter not open lights up when no. 2 feed motorhas has rotated CCW for 1 sec. 0003 While lifting the tray motor in operation, the shutter closed detectingswitch found to go when Tray 1/2 is OFF the safety area positionof detect switch.

E590

The main cause of the home position sensor blow (PI3P) is damaged. Motor blows(M1P) damaged. Driver PCB is faulty punch. Fashion ofDetection0001 pons has not left the House when the motorhas punch position had been encouraged to 200 msecs. 0002 pons did not return to the home position when the motorhas punch has been encouraged to 200 msecs.

E593

The main cause of the House registration horizontal position sensor (PI1P) is broken. Motor horizontalregistration (M1P) damaged. Driver PCB is faulty punch. FashionofDetection0001 pons has not left the House when the horizontal position of the registrationmotor had driven for 4 secs. 0002 pons did not return to the home position when the motor horizontalregistration has pushed for 4 seconds.

E5F0

The main causes of home plate position paper sensor position (PI7S) is broken. Motor plate paperpositioning (M4S) damaged. Saddle stitcher controllerPCB is faulty. Fashion ofDetection0001 Position paper home plate position sensor does not light up onwhen position paper plates of the motor has been boosted to about 1.3 secs. 0002 Position paper home plate sensor position unchanged off1 seconds after the motor plate position paper that has been encouraged to 1sec.

E5F1

The main causes of motor sensor Clock folding (PI4S) is broken. The paper folding homeposition sensor (PI21S) is broken. The folding motorbike (M2S) damaged. Thesaddle controller PCB faulty stitcher. OfDetection0001 quantity of detection mode sensordrops clock motor that fold under certain circumstances value. this position of the sensors 0002 paper folding home not notchange when folding motor has pushedfor 3 seconds.

E5F2

The main cause of the home position sensor Guide (PI13S) is broken. Motor guide (M3S) damaged. Saddle stitcher PCB controller is faulty. Fashion ofDetection0001 Home position sensor guide does not light up when the guidemotor has been boosted to around 0.5 sec. 0002 Home position sensor guide does not turn off when the guidemotor has been boosted to 1 second.

E5F3

The main cause of the home position sensor alignment (PI5S) is broken. Motor alignment (M5S) damaged. Saddle stitcher PCB controller is faulty. OfDetection0001 fashion plate of the congruence of the House position sensor does not light up on motor alignment whenthe have driven to 0.5 seconds (originally, drivenfor about 1.7 seconds) 0.0002 Plate alignment position sensor does not switch off home whenthe motor alignment has been boosted to 1 second.

E5F4

The main cause of stitch Home sensor position (back, MS5S) is broken. Motorcycle stitch (rear, M6S) damaged. Saddle stitcher PCB controller is faulty. Mode of 0001 Detection Home stitcher (rear) position sensor does not switch off when the motor thestitch (rear) has rotated CW during 0.5 seconds or more. the home position Sensor 0002 skewer (rear) does not light up when the motor thestitch (rear) has rotated CCW for 0.5 seconds or more.

E5F5

The main causes of home position skewer Sensor (front, MS7S) is broken. Motorcycle stitch (front, M7S) damaged. Saddle stitcher PCB controller is faulty. Home ofDetection0001 stitch mode position sensor (front) does not switch off when the motor thestitch (front) has rotated CW during 0.5 seconds or more. 0002 Home stitch position sensor (front) not lit at the time of the motor thestitch (front) has rotated CCW for 0.5 seconds or more.

E5F6

The main cause of push-hours on paper plate motor sensor (PI1S) is broken. The paperpush-on the plate the tip leading position sensor (PI15S) is broken. The paperpush-at home plate position sensor (PI14S) is broken. Push-onplate motor (M8S) paper is broken. Saddle stitcher PCB controller is faulty. OfDetection0001 push-mode sensor on top of the paper plate to position the House not lit onwhen paper push-on motor plate have been encouraged to 0.3 minutes ormore. 0002-sensor push on paper plates home position does not turn offwhen paper push-on motor plate have been encouraged to 0.3 minutes ormore. 0003 push-on paper plate edges leading position sensor does not turn when the push-on paper plates of the motor has been encouraged to 0.3 Secor more. 0004 toll Number detection paper push-on motorclock plate sensor falls below a certain value. 0005 push-on paper the leading edge of the plate sensor does not light up onwhen paper push-on motor plate have been encouraged to 0.3 seconds or more.

E5F8

The main cause of the home position sensor Guide (PI13S) is broken. Push-on papersensor position of platehome (PI14S) is broken. Push-on paper sensor position leadingedge plate (PI15S) is broken. Saddle stitcher isfaulty controller PCB. Fashion ofDetection0001 position sensor Connector from home Guide found bedisconnected. 0002 Connector paper home positionsensor home plate position found to be disconnected. 0003 Connector push-in paper plate leading positionsensor the banks found to be satisfied.

E5F9

The main cause of the entrance switch (MS1S) is broken. Switch front door (MS2S) isfaulty. Door delivery switch (MS3S) is broken. Saddle stitches controllerPCB is faulty.Detection mode of 0001 When closing the inlet, front cover, and the cover is closed, the switch is foundto delivery entrances detect conditions open to 1sec or more of the beginning of the rotation early host of early printing machineor. 0002 When closing the inlet, front cover, and includes delivery found tobe is closed, the switch detects the condition of the front door open for 1 more Secor after the start of the rotation early early masters orthe 0.0003 molding machine When the cover inlet , front cover, and includes delivery found tobe closed, door switches detect conditions open to 1sec or more of the beginning of the rotation early machineor host start printing.
A common Error code on Canon Copy Machine IR 2870/3570/4570/3030/3035/3045/3245 Rating: 4.5 Diposkan Oleh: MY BLOGGER